News

BAY51-Q _ x_ _ series explosion-proof plastic light fittings for fluorescent lamp is usable for lighting in the petroc

II CT4 ' 2. High pressure sodium /mercury / halide lamp '3. AC220v 50Hz ' 4. IP65 5. Zone 1 &2 6. ATEX certified.

Liquid and coarse particle suction - Ab500Ex High material collection capacity Easy handling ATEX approved Single

Explosion proof motors (Flame proof d Type) ATEX (France) KGS (Korea) Standard Specification SPECIFICATION ITEMS

ATEX certifications (only for EExd BT4), and also complied with the Essential Health and Safety Requirements of CENELEC

Simple single button operation, small size and weight make the Crowcon Tetra 3 the easiest to use gas detector on the market.

Based on the proven and highly successful Tetra product, the Crowcon Tetra 3 is designed for use in demanding industrial environments. Despite its compact size the Crowcon Tetra 3 is ultrarugged and waterproof.

Meets ATEX approvals ATEX II 2G EEx iad IIC T4 (Tamb -20°C to +55°C) BASEEFA05ATEX0187

The four gases detected by the Crowcon Tetra 3 are:

• Flammable 0-100% LEL
• Oxygen 0-25%
• Hydrogen Sulphide 0-50ppm
• Carbon Monoxide 0-500ppm

Supplied with batteries
Manufacturer: Crowcon
Part No : CROTET3-CH4-H2S-02-C0

Designed for hazardous environments, the Digitron P200L is suitable for use with non-corrosive, non-ionic liquids and gases. Liquid pressure can be measured using an air buffer.

The Digitron P200L measures from 0-199.9mbar on the low range to 0-500mbar on the high range. Connections are push fit 4mm/0.157" I.D. 6MM/0.236" O.D. nominal, retaining nut supplied.

Certified by BASEEFA, the UK's leading ATEX approvals house, the Digitron P200L is classified as EEx ia IIC T4. This certification is equivalent to EN 50 014:1997 + Amendments 1&2 and EN50 020:2002. The units are ready for site use anywhere, immediately.

Case proven the tough construction of the Digitron P200L makes them extremely durable and, therefore functional in not only hazardous atmospheres but also rough environments.
Manufacturer: Digitron
Part No : DIGP200L

Based on the Fluke 87V, the Fluke 87VEx has all the measurement and troubleshooting functions that the Fluke range offers.

Unlike most other ATEX-certified tools, the Fluke 87VEx can be used both inside and outside the hazardous zone (ATEX Zones 1 & 2, safety rating II 2G EEx ia IIC T4) without compromising performance or compliance, so there's no need to carry different tools for use in different areas. The Fluke 87VEx also has a built-in thermometer with TC probe, further reducing the need to purchase extra ATEX tools, which can be costly.

The key features of the Fluke 87VEx are:

• True-RMS voltage and current for accurate measurements on non linear signals
• 20kHz Bandwidth
• Selectable filter for accurate voltage and frequency measurements on motor drives
• Large backlit LCD display with analogue bargraph
• Auto & manual ranging for maximum flexibility
• Min-Max-Average

An ATEX approved loop calibrator for use in explosion endangered areas. The Fluke 707Ex is certified in accordance with the ATEX directive (Ex II 2 G Eex ia IIC T4) in Zones 1 and 2.

The Fluke 707Ex is a high performance solution for calibration, repair and maintenance of current loops. The new "Quick Click" knob makes it extremely fast and easy to use.

Features of the Fluke 707Ex include:

• One handed user interface with "Quick Click" detented knob, mA sourcing
• Simulation and measurement, 0.025% accuracy and 0.001mA resolution
• Simultaneous mA and % of span display
• Selectable step or ramp outputs
• 24 V Loop supply with mA measure including 250Ω HART resistor & 0-28 VDC measurement to check Loop Voltage

Supplied with red holster, TL75 test leads, alligator clips, battery and intruction sheet.
Manufacturer: Fluke
Part No : FLU707EX

The Seaward Type C is designed to measure voltage from 80 - 650V AC / DC. Previously classed as "Intrinsically Safe" for use in hazardous areas, it should be noted that this item DOES NOT meet the current ATEX standard. Please Click Here to read the compliance statement from Seaward.

The Seaward Type C conforms to BS1259 for Intrinsically safe circuits and to the UK Electricity Council Engineering Recommendation G9.

The Seaward Type C is a neon voltage indicator, enclosed within shock resistant enclosure, and is unaffected by immersion in water.
Manufacturer: Seaward
Part No : SEAC